MDT Tru Tracker Complete Rear Track Correction System 2016 on (Fully Fitted and Approved)

MDT Tru Tracker – Complete Rear Track Correction System suitable for the V8 J70 Series Toyota Landcruiser

The Tru Tracker system is designed and engineered to be fully compliant with the Australian Design Rules (ADRs).

The price of this kit is fully fitted and approved by Superior Engineering.

All components are manufactured from high grade materials and thoroughly tested to ensure the strength and reliability of the rear axle assembly is retained.

Each component has undergone Finite Element Analysis (FEA) and has full Engineering Approval.

Easy to install, the Tru Tracker finally allows you to enjoy the benefits of putting the rear wheels where they should be!

In 2007 Toyota introduced the V8 diesel engine into its 70 Series model range in Australia. To accommodate the larger engine, the engine bay was widened and front track width was increased, while the rear remained unchanged. The result: an OEM track width difference of 95mm.


The narrower track at the rear causes the vehicle to sway unpredictably when travelling on soft surfaces. This also occurs when the vehicle encounters dry wheel ruts, or edged surface changes on sealed roads. Instability issues are also present when towing, or with heavily loaded or troop carrier vehicles with a high centre of gravity. This presents as a significant safety concern as the vehicle can become unstable and difficult to control under these conditions.


The MDT Tru Tracker is a complete rear track width correction system.

Designed and manufactured in Australia to the highest standards, the components fitted relocate the entire wheel hub assembly to the correct location.

As opposed to illegally offset rims or wheel spacers, the Tru Tracker is fully engineered & ADR complaint.

Installation is completed on vehicle with minimal modification required. The Tru Tracker also utilises many of the existing OEM components.

Toyota warranty is matched on all Tru Tracker components, with the system being available for fitment Australia wide (refer website for details).


Improved dynamic stability and handling on sealed and well-formed roads

Significantly improved tracking, driver control and handling in loose / deformable soils such as mud, gravel or sand

Improved stability when towing

Improved responsiveness

Improved rollover resistance


  • Complete Rear Axle Width Correction
  • Improved Off-Road Safety
  • Improved Vehicle Stability
  • Increased Fuel Economy
  • Utilises existing Diff Housing
  • MDT Extension Stubs installed on either side of housing using high tensile shoulder bolts & Loctite retaining + thread lock compound
  • Extended axles, brake lines, & park brake attachment plates  + more supplied
  • Can be completed on vehicle
  • Remaining Toyota components reapplied as normal


This kit wil only work with the new braced style rear diff housing OE Part Number 4211060D00
(see image below for visual reference)

For approval the kit must be fitted by Superior Engineering.

MDT Tru Tracker Complete Rear Track Correction System 2016 on (Fully Fitted & Approved)

MDT Tru Tracker Complete Rear Track Correction System 2016 on (Fully Fitted & Approved)

MDT Tru Tracker Complete Rear Track Correction System 2016 on (Fully Fitted & Approved)

Vehicle Information
Lift Height All Heights


Genuine/Non Genuine – Advertised parts are not genuine (unless specifically stated) and manufacturer references are for application purposes only. Only items that are specifically noted as Genuine OEM can be presumed as genuine parts.

Superior Engineering is not sponsored, approved, affiliated or otherwise associated with any genuine or original parts manufacturer, distributor or dealer.

Identification and Guidance Only – Photos are for identification purposes only and may be of either genuine or non-genuine parts.
All manufacturers names, symbols and descriptions on this website are used for reference purposes only, and it is not implied that any units or parts listed is the product of these manufacturers.

Original Equipment Manufacturer "OEM" part/reference numbers are listed for information/reference purposes only. Trademarks identifying these parts are those of each OEM and are the property of their owners and are not used, or authorized for use, by Superior Engineering. Cross-referenced parts from the Original Equipment Manufacturer "OEM" are listed for information purposes only.

Superior Engineering has no associations and/or claims to be associated with OEM Vehicle Manufacturers and their Companies worldwide. Any implied associations are purely coincidental and are not inferred. Superior Engineering is a supplier of fully interchangeable non-genuine spare parts (alternatives) for equipment produced by manufacturers using in accordance with law OEM Vehicle Manufacturers and their products, i.e. suspension parts, steering components, manufactured items, vehicle accessories etc. Alternative spare parts produced by Superior Engineering are manufactured according own technological documentation developed with the use of reverse engineering.

Latest Blog

Read more

New South Coast NSW Superior Engineering Stockist All Barred 4x4

Superior Engineering is proud to announce All Barred Up 4x4 as a NEW authorised Stockist for Sout...

Read more

79 Series Landcruiser HyperFlex Radius Arms

Superior Engineering is proud to announce the release of the amazing new 79 Series Landcruiser Hy...

Read more

Ford PXII Ranger Coil Conversion Kits

Convert your leaf spring PXII Ranger to a coil spring with one of our Coil Conversion Kits. Suppl...

Read more

Superior Engineering May Long Weekend Social Wheel

Come and join Superior Engineering and Powercurve Performance at our May Long Weekend Social Whee...

Read more

New QLD Stockist NDM Bosch Auto Services

Superior Engineering is proud to announce NDM Bosch Auto Services as a NEW authorised Stockist fo...

This page was generated in 1,550,508,973.0630 seconds.